______________________________________________________________________________ | File Name : TOMIFLAT.ASC | Online Date : 05/15/95 | | Contributed by : Ossie Callahan | Dir Category : ENERGY | | From : KeelyNet BBS | DataLine : (214) 324-3501 | | A FREE Alternative Sciences BBS sponsored by Vanguard Sciences | | KeelyNet * PO BOX 870716 * Mesquite, Texas * USA * 75187 | | Voice/FAX : (214) 324-8741 InterNet - keelynet@ix.netcom.com | | WWW sites - http://www.eskimo.com/~billb & http://www.protree.com | |---------------------------------------------------------------------------- The following excellent file shows another way of constructing the TOMI. ------------------------------------------------------------------------------ Author: Ossie Callanan From: Melbourne Australia Introduction: I have been experimenting and conducting research in alternative sciences for a number of years. For the last few years I have concentrated mainly on alternative, or as it was most commonly known, 'free', energy research as the results of such research have far reaching consequences for the future of the world as we know it and may decide if we have a future or not. I share the views of most other independant researchers who do not have a vested interest financially in the results of their research and are of the belief that only full disclosure of all of our results can prevent any suppression of this technology that has been taking place for so long. From a very young age I was always interested in electronics and have built a great many devices of my own design. It started becoming apparent to me, whilst studying for my diploma in electronics, that what I was being taught was established electrical and physical principles that had been worked out a great many decades ago and all I was being taught was updated uses of what was basically old science. It wasn't to long after beginning my research into alternative sciences that the reasons for this became all to apparent. I do not wish to bore you with the ignorant politics of the suppression that has been taking place as I am sure you would be aware of it already. I believe the best way to beat the suppression is to share the results so that others may duplicate and further develop the technology and not try to selfishly look to the gain of ones self at the expense of preventing the gain to a great many. One of the most important aspects of any device is its simplicity and the ability for others to duplicate it and its claimed results. One of the best I've seen so far that meets this requirement is the TOMI device or Theory Of Magnetic Instability device to which I commend the inventor. This is one such device that any body new to the new energy seen should build as it definately shows them something that works and further inspires one to take a serious look into this type of research. The purpose of this text is to give to all, my results and modifications to the TOMI device in its linear form so that it is much simpler to duplicate. If this is the first time you've heard of the TOMI device, whilst reading this text, I suggest that you first read the original and other previous texts written on the device by the inventor (Stewart Harris of Las Vegas) and his associates. (see TMIDEVIC, TOMIBILD, TOMIMOTR, & MAGSPIN on KeelyNet) ------------------------------------------------------------------------------ The Flat Linear TOMI Device After reading and duplicating the original TOMI device, I was intrigued by the need to have a track that consisted of ramps of inclination and declination although at the time I percieved that one of the requirements for the device to work was for it to utilise both gravitation and magnetic anomalies. After considerable experimentation I found that I was able to completly do away with the gravitational component of the device, which held the need for ramps of inclination and declination, and have a device that was completely driven by the magnetic anomally itself on a completely flat horizontal linear track of unlimited length. This makes duplication of the device and the result almost foolproof. All one needs to make this version of the device is a stack of button magnets (I used the round holeless ferrite type- 10mm diameter by 5 mm thick), a role of double sided tape, a little bit of masking tape and a flat table top. There is no need to make any special ramped track as the table top is used for your flat track. ------------------------------------------------------------------------------ Construction First make the roller. This is the same as described in the original TOMI device text and consists of 7 to 10 magnets of the same polar direction stuck together in a role and held together with a bit of masking tape. Next lay two parallel and straight lines of double sided tape on the table top. The distance between the two lines of tape should be the length of roller plus 1.5 to 2 inches. Peel off the top of the double sided tape and now you are ready for the most important part, the laying of the track magnets. This is the most important and unique part that I have developed, which lets the device work on a flat linear track. The track magnets are not stuck together but are individually seperated by a gap or shall I say a gap of two different distances. Place the magnets one by one on the first line of double sided tape all in the same polar direction with the polar axis parallel to the tape. In between the magnets leave a gap of a certain length and then a gap of double the length for every alternate gap. The gap distance I used for the type of magnets I had was 5 mm and 10 mm respectively. This alternation of gap distance is the key to continuous operation on a flat horizontal track. The gap distance or the fact that one is double the other is not crucial and is variable. What is crucial is the alternation of the gap distances because if they were all the same distance, the propulsive magnetic anomally will only occur at the beginning and the end of the track limiting the length of the track, this is why a ramped track was necessary in the original TOMI device. When two alternate gap distances are used, the propulsive anomally is present throughout the length of the track allowing an unlimited length of track that is flat and horizontal although it may work on a constant incline of which depends on the propulsion strength. To complete construction place another row of magnets on the other line of double sided tape except the polarities must be opposite that of the first line of magnets and parallel to the length of the track. Make sure that the magnets line up perpendicular to the length and in line with the magnets on the other line of tape. Now that you have finished the track all you have to do is place the roller anywhere in the track (perpendicular to the length of the track of course) and it will roll in its appropriate polar direction till it reaches the end of the track. The roller may be turned over swapping its own polar direction and you will find it will also roll in the opposite direction till it reaches the end of the track. ------------------------------------------------------------------------------ I also recommend people who have duplicated this device, try and develop it into some form of rotary rotor type orientation which in effect will make it a permanent magnet motor requiring now input energy. I am continuing in this direction myself though at present I make no claims to having done so and personally do not release any results of my research until I have a working model myself. I recommend anyone researching the field of alternate energy to make this device as I feel that a duplicatable working device is worth a thousand theories. ------------------------------------------------------------------------------